Engine

Selected Engine:

B58

Models:

BMW 340i/ix F30 F31 F34     |    

BMW 440i/ix F32 F33 F36     |    

BMW M240i/ix F22     |    

BMW M140i F20     |    

    |    

    |    

    |    

    |    

Selected stage:

99 USD/EUR

STAGE 1

99 USD/EUR

STAGE 2

99 - Soon

STAGE 3

180 USD/EUR

Engine parameters

Stock
HP

343 HP

Torque

488NM/ 360lb ft

after
HP

430 HP

Torque

610NM/ 450lb ft

For a point of reference, displayed power output of original software is based of our measurement on our dyno. This can give you an idea of the exact delta gain of our software vs the various stages of what is considered stock software.

ORIGINAL Baseline: 343 HP 488NM / 360 ft lb - measured by our dyno
ORIGINAL Baseline: 322 HP 450NM / 332 ft lb - BMW factory specification

Dyno diagrams

Gasoline

91/95
RON

93/98
RON

Supported models

BMW 340i/ix
F30 F31 F34
322 HP, 450 NM (332 LB-FT)
355 HP, 500 NM (369 LB-FT) - MPPSK version
BMW 440i/ix
F32 F33 F36
322 HP, 450 NM (332 LB-FT)
355 HP, 500 NM (369 LB-FT) - MPPSK version
BMW M240i/ix
F22
335 HP, 500 NM (369 LB-FT)
BMW M140i
F20
335 HP, 500 NM (369 LB-FT)








Additional info

POWER INCREASE

Flashing License 249 USD/EUR - required to flash any OTS map

Up to 430HP 610NM @ Crank
Cars with stock exhaust system

Up to 410HP up to 580NM @ Crank
Cars equipped with Otto Particulate Filter (OPF)

(550NM limit without 8HP50 Transmission flash)
*Transmission Tuning Recommended*
See Transmission Limiter information below

Designed for the drivers who want the most out of their stock component vehicle. This software is intended to safely maximize your vehicle’s potential performance. The power curve has been delicately engineered to eliminate any dips in the overall powerband as well as maximizing delivery of that power throughout the entire RPM range.

TECHNICAL INFORMATION

- Boost Pressure up to 1.15 Bar (17 PSI)
- NBT Display HP/TQ gauges calibration
- Torque limiters
- Lambda optimization
- Ignition timing optimization
- Optimized for xHP transmission tuning software

Additional options available with each OTS map
- Exhaust burble adjustable on-the-fly - set the intensity without reflashing!
- Switchable maps on-the-fly - select between maps without reflashing!
- Speed limiter removal
- Cold start delete (off road use only)
- Catalytic converter delete (dcat, off road use only)
- Exhaust flap control

Transmission Limiter Information:

The 340i is equipped with an 8HP50 transmission where the factory torque limiter is set to 550NM/400ftlb tq @ the crank. For the best results and proper smoothing of the torque curve without any transmission related torque intervention we have found that is best to increase the limiter within the transmission software. We present you with two options to implement this on your vehicle:

Option 1: Lifting the limiter in the transmission ECU which can be done for example with xHP Flash tool
Option 2:Bringing the car to our shop or another tuner for reprogramming of the transmission ECU limiters

We also support ETHANOL BLEND E20 up to E30 Mix

Engine parameters

Stock
HP

343 HP

Torque

488NM/ 360lb ft

after
HP

470 HP

Torque

650NM/ 481lb ft

For a point of reference, displayed power output of original software is based of our measurement on our dyno. This can give you an idea of the exact delta gain of our software vs the various stages of what is considered stock software.

ORIGINAL Baseline: 343 HP 488NM / 360 ft lb - measured by our dyno
ORIGINAL Baseline: 322 HP 450NM / 332 ft lb - BMW factory specification

Dyno diagrams

Gasoline

91/95
RON

93/98
RON

Supported models

BMW 340i/ix
F30 F31 F34
322 HP, 450 NM (332 LB-FT)
355 HP, 500 NM (369 LB-FT) - MPPSK version
BMW 440i/ix
F32 F33 F36
322 HP, 450 NM (332 LB-FT)
355 HP, 500 NM (369 LB-FT) - MPPSK version
BMW M240i/ix
F22
335 HP, 500 NM (369 LB-FT)
BMW M140i
F20
335 HP, 500 NM (369 LB-FT)








Additional info

POWER INCREASE

Flashing License 249 USD/EUR - required to flash any OTS map

Up to 470HP 650NM @Crank

Use only with High Flow Downpipe
or High Flow Catalytic Converter

For the spirited drivers who want the maximum power out of their vehicle equipped with high flow downpipe or high flow catalytic converter. This software is intended to maximize your vehicle’s potential performance. The power curve has been delicately engineered to eliminate any dips in the overall powerband as well as maximizing delivery of that power throughout the entire RPM range.

*Transmission Tuning Recommended*
See Transmission Limiter information below

TECHNICAL INFORMATION

- Boost Pressure up to 19 PSI (1.3 Bar)
- NBT Display HP/TQ gauges calibration
- Torque limiters
- Lambda optimization
- Ignition timing optimization
- Optimized for xHP transmission tuning software

Additional options available with each OTS map
- Exhaust burble adjustable on-the-fly - set the intensity without reflashing!
- Switchable maps on-the-fly - select between maps without reflashing!
- Speed limiter removal
- Cold start delete (off road use only)
- Catalytic converter delete (dcat, off road use only)
- Exhaust flap control

Transmission Limiter Information:

The 340i is equipped with an 8HP50 transmission where the factory torque limiter is set to 550NM/400ftlb tq @ the crank. For the best results and proper smoothing of the torque curve without any transmission related torque intervention we have found that is best to increase the limiter within the transmission software. We present you with two options to implement this on your vehicle:

Option 1: Lifting the limiter in the transmission ECU which can be done for example with xHP Flashtool
Option 2:Bringing the car to our shop or another tuner for reprogramming of the transmission ECU limiters

We also support ETHANOL BLEND E20 up to E30 Mix

OTS maps for *Ethanol* Blend E20 up to E30 Mix

Engine parameters

Stock
HP

343 HP

Torque

488NM/ 360lb ft

after
HP

0 HP

Torque

0NM/ 0lb ft

For a point of reference, displayed power output of original software is based of our measurement on our dyno. This can give you an idea of the exact delta gain of our software vs the various stages of what is considered stock software.

ORIGINAL Baseline: 343 HP 488NM / 360 ft lb - measured by our dyno
ORIGINAL Baseline: 322 HP 450NM / 332 ft lb - BMW factory specification

Dyno diagrams

Gasoline

91/95
RON

93/98
RON

Supported models

BMW 340i/ix
F30 F31 F34
322 HP, 450 NM (332 LB-FT)
355 HP, 500 NM (369 LB-FT) - MPPSK version
BMW 440i/ix
F32 F33 F36
322 HP, 450 NM (332 LB-FT)
355 HP, 500 NM (369 LB-FT) - MPPSK version
BMW M240i/ix
F22
335 HP, 500 NM (369 LB-FT)
BMW M140i
F20
335 HP, 500 NM (369 LB-FT)








Additional info

**Under development**

Flashing License 249 USD/EUR - required to flash any OTS map

ALL OTS PACK

Flashing License 249 USD/EUR - required to flash any OTS map

It is the most convenient and economical all-in-one package. All available OTS maps (Stage 1, Stage 2 Stage 3) included for your car with the same VIN number - choose it and have no more hassle of upgrade costs in the future!. This package will allow you to switch between maps of your choice! In case you already purchased single OTS map and decide you would like to update your OTS map to different (higher or lower) versions, you will be presented with the option for a FULL OTS Map Pack at a discounted price.





no stage

stage 1

stage 2

stage 3

custom

Additional options

Switchable maps

Switchable Maps - through a simple combination of the Brake Pedal, Accelerator Pedal, Traction Control Button and the Driver Select Switch you can quickly select between E30 and Regular Octane mapping, without the need to reflash vehicle.

Exhaust burble

Our unique function Dynamic Burble on the Fly - with this function via a simple combination of the Driving Experience Switch and the MSA button you can change the intensity of the burbles ON THE FLY!
This feature comes at no additional cost.

There are 4 switchable levels available including Burble OFF in all modes. Watch our instructional video on Youtube or Facebook page - read User Manual for detailed instruction

Youtube Video

Cold start with cat heating delete

Want to be a good neighbour, or going CAT-Less? MG Flasher has got you covered with cold start delete. No more loud cold startups. This feature comes at no additional cost.

Speed limit removal

Unleash your BMW's true potential:
Remove the factory set top speed limiter - With just a tap in the MG Flasher! This feature comes at no additional cost.

Catalytic converter delete

For those of you guys who want to squeeze out the maximum potential out of this powerful B58 platform, we have an option for going with cat-less downpipes and corresponding tune. Disclaimer: This option is for off road/racing use only.

Additional options

Exhaust burble

Our unique function Dynamic Burble on the Fly - with this function via a simple combination of the Driving Experience Switch and the MSA button you can change the intensity of the burbles ON THE FLY!
This feature comes at no additional cost.

There are 4 switchable levels available including Burble OFF in all modes. Watch our instructional video on Youtube or Facebook page - read User Manual for detailed instruction

Youtube Video

Cold start with cat heating delete

Want to be a good neighbour, or going CAT-Less? MG Flasher has got you covered with cold start delete. No more loud cold startups. This feature comes at no additional cost.

Speed limit removal

Unleash your BMW's true potential:
Remove the factory set top speed limiter - With just a tap in the MG Flasher! This feature comes at no additional cost.

Catalytic converter delete

For those of you guys who want to squeeze out the maximum potential out of this powerful B58 platform, we have an option for going with cat-less downpipes and corresponding tune. Disclaimer: This option is for off road/racing use only.

Switchable maps

Switchable Maps - through a simple combination of the Brake Pedal, Accelerator Pedal, Traction Control Button and the Driver Select Switch you can quickly select between E30 and Regular Octane mapping, without the need to reflash vehicle.

Additional options

Exhaust burble

Our unique function Dynamic Burble on the Fly - with this function via a simple combination of the Driving Experience Switch and the MSA button you can change the intensity of the burbles ON THE FLY!
This feature comes at no additional cost.

There are 4 switchable levels available including Burble OFF in all modes. Watch our instructional video on Youtube or Facebook page - read User Manual for detailed instruction

Youtube Video

Cold start with cat heating delete

Want to be a good neighbour, or going CAT-Less? MG Flasher has got you covered with cold start delete. No more loud cold startups. This feature comes at no additional cost.

Speed limit removal

Unleash your BMW's true potential:
Remove the factory set top speed limiter - With just a tap in the MG Flasher! This feature comes at no additional cost.

Catalytic converter delete

For those of you guys who want to squeeze out the maximum potential out of this powerful B58 platform, we have an option for going with cat-less downpipes and corresponding tune. Disclaimer: This option is for off road/racing use only.

Switchable maps

Switchable Maps - through a simple combination of the Brake Pedal, Accelerator Pedal, Traction Control Button and the Driver Select Switch you can quickly select between E30 and Regular Octane mapping, without the need to reflash vehicle.

Subscribe to MG-Flasher

Keep yourselves in the loop by subscribing to our newsletter.

footer